Syncros Trail DH Fender Fox 40 49 black Mudguard

Product Information

Our lower leg bleeders allow for atmospheric pressure equalization at the simple press of a button. Pressure build-up in the lower legs dramatically decreases fork performance, preventing full travel from being achieved, and diminishing small bump sensitivity and responsiveness. Stiffer Lower Leg Arch Modern frame designs and geometry trends require modern suspension design solutions. The arch design of the all-new 36, 38, and 40 is designed to pair perfectly with modern Enduro and Downhill bikes. Head tube profiles have grown larger and larger, and fork offsets shorter and shorter. Our new arch shape takes this need into account by jutting forward to provide ample headtube clearance at full compression. State-of-the-art computer modeling techniques helped us to create an organic lower leg shape that optimizes stiffness with the absolute minimal amount of material. More Tunable GRIP2

MINI & STANDARD COMPATIBILITY WHEELS: 26” 27.5” 29” TYRES: up to a 3” tyre BRAKE / OFFSET: MINIMUM 44mm HUB: STD & BOOST FORKS:You should be able to locate the mudguard and let go as the rubber side pads should hold it in place (ensure the slots are centrally aligned to the threaded holes on your fork) Crud Products XL Front Fender 6. Crud Products XL Front Fender Pricey but worth it if you need to remove/attach frequently Finally tighten the bolts to the torque settings below: TORQUE SETTINGS: FOX, MARZOCCH & OHLINS = 1nm | SR SUNTOUR = 2nm COMPATIBILITY WHEELS: 26” 27.5” 29” TYRES: up to a 3” tyre BRAKE / OFFSET: MINIMUM 44mm HUB: STD & BOOST FORKS: Select the correct bolts for your fork (details below) and run these into the threads WITHOUT the mudguard which will 'PRIME' and clean the threads before fitting, this part is important (YOU MAY NEED TO RE-TAP THE THREADS IF DEBRIS / PAINT IS LEFT IN THE THREADS FROM THE MANUFACTURE OF THE FORKS) BOLTS: FOX = M3 (2 bolts) | OHLINS = M4 (3 bolts) | SR SUNTOUR = M6 ( *1 bolt)

The ProGuard BOLT ON will fit most fork models listed below if they have the *THREADED HOLES at the rear of the fork brace (DISK BRAKE ONLY): WHEELS: 26” 27.5” 29” TYRES: up to a 3” tyre BRAKE / OFFSET: MINIMUM 44mm HUB: STD & BOOST FORKS: The benefits of EVOL are further enhanced by our new Lower Leg channels and Bleeders, which both function to reduce air pressure captured in the lower legs, allowing the EVOL air spring to operate freely without unintended interference. Specifications Floating axles might look similar to other axles, but in fact they offer a distinct performance advantage due to their unique ability to match the exact width of the fork’s wheel mounting surface precisely to the front hub flange spacing, thus creating perfect chassis alignment and eliminating unwanted friction between the upper and lower fork legs. Floating axles provide much smoother suspension movement throughout the entire range of the fork’s travel, notably improving sensitivity and overall ride quality. Our widely acclaimed Seal Shield offers greater protection for your fork seals from high velocity mud and spray lengthening service intervals MATERIAL Use the Allen key provided to screw the bolts in EVENLY a bit each side, go gentle to start off to ensure you DON'T CROSS THREAD THEM, stop once it's pulled together so you can still move it

Finance is subject to application, financial circumstances and borrowing history. Performance Cycling Limited FRN: 720557 trading as Tredz are authorised and regulated by the Financial Conduct Authority. We are a credit broker not a lender – credit is subject to status and affordability and is provided by Mitsubishi HC Capital UK PLC. Terms & Conditions Apply. INSPECT BEFORE YOU RIDE: DO NOT USE IF DAMAGED IN ANY WAY AS CONTINUED USE MAY LEAD TO FAILURE OR INJURY EVOL technology increases negative air spring volume, optimizing small bump sensitivity. EVOL’s linear spring curve delivers plushness off the top, extra mid-stroke support, and more tunable bottom-out progression. You can also change the height of the mudguard by 6mm through the slots for more clearance. NOTE: Highest position offers the most stability with the best mud clearance All the mudguards in this test mount under the suspension fork brace, however, there is limited space between the fork crown and tire. If you are running 29-inch wheels with tall tires, the mudguard will fit very close to the tire. As a rule of thumb, it is best to ensure there is at least 18 mm of clearance (about the width of your index finger) between the mudguard and the tire to avoid rubbing. Once the mudguard is fitted, It is recommended that you release all the air pressure from your fork and compress it to its maximum travel to make sure the fork lowers do not hit the mudguard. Will my MTB mudguard break in a crash?

The granting of a best price is not combinable with other promotions (e.g. "free articles) from Bike-Discount. The ProGuard - BOLT ON is our direct mount front mountainbike mudguard designed for big spray and mud protection (DISC BRAKE ONLY)RapidRacerProducts Ltd accepts no liability for any damage or injury caused due to improper fitting or use of our products IMPORTANT: You must apply the rubber adhesive side pads to the recess on the mudguard side wings, they protect your fork legs and provide vital stability and resonance damping Another benefit of these channels is that lower leg bath oil is circulated to the upper reaches of the lower legs, continuously lubricating the foam rings and bushings as the fork compresses and extends through its travel. Bleeders